GICD_IPRIORITYR<n>E, Holds the priority of the corresponding interrupt for each extended SPI supported by the GIC., n = 0 - 255

The GICD_IPRIORITYR<n>E characteristics are:

Purpose

Holds the priority of the corresponding interrupt for each extended SPI supported by the GIC.

Configuration

This register is present only when GICv3.1 is implemented. Otherwise, direct accesses to GICD_IPRIORITYR<n>E are RES0.

When GICD_TYPER.ESPI==0, these registers are RES0.

When GICD_TYPER.ESPI==1, the number of implemented GICD_IPRIORITYR<n>E registers is ((GICD_TYPER.ESPI_range+1)*8). Registers are numbered from 0.

Attributes

GICD_IPRIORITYR<n>E is a 32-bit register.

Field descriptions

31	30	29	28	27	26	25	24	23	22	21	20	19	18	17	16	15	14	13	12	11	10	9	8	7	6	5	4	3	2	1	0
Priority_offset_3B								Priority_offset_2B								Priority_offset_1B								Priority_offset_0B

Priority_offset_3B, bits [31:24]

Interrupt priority value from an IMPLEMENTATION DEFINED range, at byte offset 3. Lower priority values correspond to greater priority of the interrupt.

The reset behavior of this field is:

On a GIC reset, this field resets to an architecturally UNKNOWN value.

Priority_offset_2B, bits [23:16]

Interrupt priority value from an IMPLEMENTATION DEFINED range, at byte offset 2. Lower priority values correspond to greater priority of the interrupt.

The reset behavior of this field is:

On a GIC reset, this field resets to an architecturally UNKNOWN value.

Priority_offset_1B, bits [15:8]

Interrupt priority value from an IMPLEMENTATION DEFINED range, at byte offset 1. Lower priority values correspond to greater priority of the interrupt.

The reset behavior of this field is:

On a GIC reset, this field resets to an architecturally UNKNOWN value.

Priority_offset_0B, bits [7:0]

Interrupt priority value from an IMPLEMENTATION DEFINED range, at byte offset 0. Lower priority values correspond to greater priority of the interrupt.

The reset behavior of this field is:

On a GIC reset, this field resets to an architecturally UNKNOWN value.

Additional information

For interrupt ID m, when DIV and MOD are the integer division and modulo operations:

The corresponding GICD_IPRIORITYR<n> number, n, is given by n = (m-4096) DIV 4.
The offset of the required GICD_IPRIORITYR<n>E register is (0x2000 + (4*n)).
The byte offset of the required Priority field in this register is m MOD 4, where:
- Byte offset 0 refers to register bits [7:0].
- Byte offset 1 refers to register bits [15:8].
- Byte offset 2 refers to register bits [23:16].
- Byte offset 3 refers to register bits [31:24].

Accessing GICD_IPRIORITYR<n>E

When affinity routing is not enabled for the Security state of an interrupt in GICD_ISACTIVER<n>E, the corresponding bit is RES0.

When GICD_CTLR.DS==0:

A field that corresponds to a Group 0 or Secure Group 1 interrupt is RAZ/WI to Non-secure accesses.
A Non-secure access to a field that corresponds to a Non-secure Group 1 interrupt behaves as described in Software accesses of interrupt priority.

Bits corresponding to unimplemented interrupts are RAZ/WI.

Note

Implementations must ensure that an interrupt that is pending at the time of the write uses either the old value or the new value and must ensure that the interrupt is neither lost nor handled more than once. The effect of the change must be visible in finite time.

GICD_IPRIORITYR<n>E can be accessed through the memory-mapped interfaces:

Component	Frame	Offset	Instance
GIC Distributor	Dist_base	0x2000 + (4 * n)	GICD_IPRIORITYR<n>E

Accesses on this interface are RW.

26/03/2024 09:49; 67c0ae5282a7629ba0ea0ba7267b43cd4f7939f6